Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

Best Black Friday E-Bike Deals 2024 | Up to $1,700 in Savings

New: Take Part in the November Giveaway: Starts November 18th


Quill stem issue
#1
Hi guys,

I'm looking for help with a bike I bought about a week ago, I would stress that this bike is brand new, not used before.

The bike arrived mostly assembled and one thing I needed to do was slot the handlebars + stem into the bike frame and tighten the bolt in order to hold the stem tight so it turns with the front wheel.

However when I tighten the bolt the handlebars + stem are still able to move with relative ease. I have attached some photos to help explain the problem.

As you can see when I move the front wheel the stem and handlebars move with it as they should, however when I clamp the front wheel I am able to move rotate the handlebars (as in the stem is moving) with ease. I would also point out that the bolt at the top is very tight and I am still able to create the rotation with ease. Also is a picture of the wedge to show that it is tightening as intended.

I may just be being very stupid but I'm totally baffled. I have contacted the seller and they are trying to help but I wanted another opinion on this to make sure it is a fault and not just me being daft. I am not literate in cycling language so please keep that in mind with any suggestions.

Thanks for reading and thanks in advance for any help you may try and give.
  Reply
#2
Measure the inside diameter of the fork with calipers in mm). Compare to what's written on the stem.
  Reply
#3
It could also be that someone has swapped out the bolt and you have bottomed out the threads before it has tightened proper
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
  Reply
#4
(10-21-2014, 07:14 PM)painkiller Wrote:  It could also be that someone has swapped out the bolt and you have bottomed out the threads before it has tightened proper
^^^^^^^^^^^^^^^
With a new bike I doubt the stem would be the wrong size. But worth checking. Quality control is a farce.

But yes do check the bolt to see if its threaded high enough and check the angled faces for burr. Put a little bit of grease on it and try again. With a small wrench do not go gorilla on it.
Never Give Up!!!
  Reply
#5
"With a new bike I doubt the stem would be the wrong size. But worth checking. Quality control is a farce"
You never know what you are going to get. I bought a Cannondale out east for my daughter back in 96' to surprise her for her B-day. I never test rode it, I just bargained a deal with the shop because i told them I was just passing through and they would never see me again, they took my offer and I hit the road. It turned out to have an 8 speed shifter on a 7 speed bike. I forced the Cannondale dealer in town to make it right, I went to pick it up and they wanted to charge me for the 7 speed shifter and never handed me the 8 speed shifter. I told them just keep the 8 speed shifter like you must have intended to in the first place, we are even thanks for nothing and walked out. then a couple years ago went to put a rack on it and noticed the hole mount was faulty with a chunk of something in the threads and then it made it thru the paint line.
Made in the USA! MMmm
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
  Reply
#6
There is one rare and unpleasant possibility. It's possible by over-torquing the bolt to distort the fork column so that the stem will no longer hold. NOT easy to do, but possible.
  Reply
#7
There is one rare and unpleasant possibility. It's possible by over-torquing the bolt to distort the fork column so that the stem will no longer hold. NOT easy to do, but possible.
[/quote]

^^^^^^^^^^^^^^^^

Man that would take a lot of gorillas. I think the threads would strip first. But then I have seen some weird stuff . We are guessing here without input from OP.
Never Give Up!!!
  Reply
#8
A LOT of strange things passed through my hands in over 20 years of wrenching - I listed that because I have seen it happen - though I believe it was on less expensive bikes, or ones that were tightened down hard and subject to an accident. The stem should always be tightened so that it gives on sudden impact.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
2,483
05-01-2024, 10:31 AM
Last Post: Nutribun
 
2,362
01-27-2024, 08:38 AM
Last Post: Talha
 
7,986
12-08-2019, 08:18 AM
Last Post: CharleyFarley
 
8,763
02-24-2017, 12:45 PM
Last Post: Mountain
 
17,196
03-19-2014, 11:02 AM
Last Post: nfmisso
 
7,958
01-11-2014, 04:16 PM
Last Post: mhaughee
 
15,800
08-22-2013, 08:23 PM
Last Post: Painkiller

Forum Jump:

[-]
10 Latest Posts
Recording Bike Rides
Yesterday 01:37 AM
Ketone Ester $$$
11-19-2024 01:04 AM
Trek domane tyre
11-18-2024 01:58 PM
Old fossil buys Ebike
11-17-2024 06:39 AM
Bike bus
11-17-2024 12:14 AM
Second wheelset for ebike.
11-16-2024 08:20 PM
Humber "Eiffel Safety" bike 1800s
11-16-2024 03:05 PM
Moving in Style: Beyond Regular Transpor...
11-15-2024 03:01 PM
Great UK Cycle Camping Map, For E-Bikes,...
11-10-2024 06:55 AM
Cycling is Anti-Aging, But There's a Cat...
11-10-2024 06:48 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Jesper
22 posts
no avatar 2. enkei
19 posts
no avatar 3. GirishH
14 posts
no avatar 4. ReapThaWhirlwind
11 posts
no avatar 5. Flowrider
11 posts