Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take part in the August Giveaway for a brand new Street Bicycle Core Line fixed gear bike


Gears aren't shifting
#1
hey, i've just replaced the gear cable on my bike and now for some reason my shifter will only allow me to change between gears 7 and 8, also my shifter reads that I am in 1st gear even though i'm in eighth! how do I sort these problems? help please.
  Reply
#2
When installing a new cable, the derailleur should be in the outer most position and the shifter should also be in the setting for the highest/hardest gear (the position where it allows the most slack in the cable). It sounds like either the shifter or derailleur was in the wrong spot when you attached the cable.

I'm assuming you have the normal set up where the derailleur spring pushes it to the outer gears and the shifter pulls it up to the inner ones. If not, then reverse my suggestion.
  Reply
#3
yeh i think thats the problem, thanks for the help, but do you know how i fix this problem because i cant move the shifter to the reading it should be on
  Reply
#4
Undo the cable from the derailleur.
Now pull on the wire and operate the shifter to go to the appropriate number.
Next turn the cranks and let the dearilleur run to the last sprocket.
Re-connect the cable (pulling it taught at the same time) and then try the shifting.

Also check that you are using the correct cable.
See:- http://www.bikeman.com/content/view/1641/115/
You should have either cable "D" or "E" depending if Shimano or Campag' changers.
Also make sure that the "head" (cable end) of the cable is properly seated in the little hole where it fits.
If it's sticking out a bit, it will stop the gears working properly
Ride hard or ride home alone!
  Reply
#5
thanks for the help Smile
  Reply
#6
Arrgghh! i tried what you suggested and my gears will still only shift between 7 and 8 Sad
  Reply
#7
Check the cable tension. Drop the derailleur to the highest gear (small cog). Slack in the cable? Undo fixing bolt, pull cable taunt. Tighten fixing bolt. *As the bolt is undone, make sure shifter is on the right number. Fine tune with the barrel adjuster at the shifter. Park Tools has some good tutorials on their web site.
GO RIDE...
  Reply
#8
First thing to do now is find the culprit!

Disconnect the cable.
Hold and pull the cable while operating the shifter.
Does the shifter go through the full range of movement / clicks?

Support the back wheel off the ground (or turn bike over and rest on saddle and bars.)
Turn the pedals/cranks and move the derailleur by hand. Does the derailleur go the whole way across the block?
You could do this first if you want to?

** Keep your fingers away from the spinning wheel. **
Ride hard or ride home alone!
  Reply
#9
I disconnected the cable and moved the derailer by hand and it does go through the full range of movement however when i disconnect and pull the cable i can still only shift between 2 gears.
  Reply
#10
So we now know it's not the RD.
What kind of shifter do you have? (make & model).
Also pull out and remove the cable and see if the shifter goes through it's movement.
Ride hard or ride home alone!
  Reply
#11
My shifter is a Shimano CI- deck plus/
  Reply
#12
Is this it:-
http://techdocs.shimano.com/media/techdocs/content/cycle/SI/NonSeries/ID-TX50/SI-6XJ0A-En_v1_m56577569830606035.pdf

Seems very complicated just to know what gear is selected.
So now you need to find if it's the changer or gear indicator that's causing the problem.
It may be a time to visit your LBS if you can't isolate it.
Have you tried removing the cable completely and see if that makes a difference.
Ride hard or ride home alone!
  Reply
#13
Its okay now i fixed the problem
  Reply
#14
(02-14-2010, 01:35 PM)andr5w5 Wrote:  Its okay now i fixed the problem

Excellent!
Are you going to tell us how - for future reference?
Ride hard or ride home alone!
  Reply
#15
Well i don't really know how to explain but there was a small lever inside the shifter which when it was pulled allowed me to shift the gears, but I've had to replace the dérailleur hanger because it was bent and don't know if that may have caused a problem as well.
  Reply
#16
I don't know what the small lever would be but the bent hanger could upset the gear change.
Usually though it wouldn't stop the gears from moving as you found out when manually moving the rear derailleur.
I'm a bit dubious about the small lever jamming unless it was caused with the installation of the cable.
Anyway well done and next time you have a good idea of where to start.
Ride hard or ride home alone!
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
Need to replace drum brakes but can’t id...
Today 01:04 AM
1983 Raleigh Super Course 12-speed
Yesterday 04:36 PM
Converting Townie 8D ebike to trail bike
Yesterday 01:20 AM
Gravel or fat bike for winter commute?
Yesterday 01:04 AM
State Bicycle Core Line | August 2020
08-10-2020 08:22 PM
Help me identify my new bike!
08-10-2020 03:47 PM
electric trikes- advice
08-10-2020 03:34 PM
Bike ride and wild camp
08-10-2020 02:45 PM
Waterford R-33 - Selling Advise
08-10-2020 01:42 PM
Hey everyone
08-10-2020 12:44 PM

[-]
Top 5 Posters This Month
no avatar 1. Jesper
52 posts
no avatar 2. Painkiller
16 posts
no avatar 3. Papa Dom
9 posts
no avatar 4. CharleyFarley
8 posts
no avatar 5. Sagan97
6 posts