Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Help with headset preload
#1
First time adjusting a headset and I'd like to get it right. Brand new giant reign with a carbon frame, that I do not want to damage

I finally have the preload set to where there is no play but I'm concerned that it is to tight...


Stage 1- obvious play/clunk

Stage 2- no clunk, but if I lock up the brake and push and pull hard, I can feel some very slight movement

Stage 3 - no play or movement detected

The difference between stage 2 and 3 is around a quarter turn.

However stage 2 is already quite snug and a quarter turn makes it pretty tight.
  Reply
#2
You need 3mm peeking down from the stem to top cap.

If you don't secure this exact measure you're going to have a bad time.

It's not as easy to just torque it down more when you have carbon components to worry about.
  Reply
#3
Threaded headsets will add weight though, which isn't very favorable.

It requires a quill stem (which is usually steel)
  Reply
#4
(01-28-2023, 03:52 AM)ReapThaWhirlwind Wrote:  Threaded headsets will add weight though, which isn't very favorable.

It requires a quill stem (which is usually steel)

Quill stems are NOT usually steel (unless you ride cheap bikes).. They are aluminum (and Ti) on any worthwhile racing and touring bike; cheap bikes use steel for lower cost. You can easily lighten them up with aluminum or Ti hardware. Even then there are some very high performance steel stems and bars. Often still used by track racers. I don't know or really care what mtb's are using since weight is not much of a factor when you are already sporting a heavy suspension system. Even then, my Cannondale mtb has an original aluminum quill stem from over 30 years ago.
With few exceptions, I feel that threadless stems are just ugly looking.
  Reply
#5
(09-10-2021, 04:56 PM)Weastcoast99 Wrote:  First time adjusting a headset and I'd like to get it right. Brand new giant reign with a carbon frame, that I do not want to damage

I finally have the preload set to where there is no play but I'm concerned that it is to tight...


Stage 1- obvious play/clunk

Stage 2- no clunk, but if I lock up the brake and push and pull hard, I can feel some very slight movement

Stage 3 - no play or movement detected

The difference between stage 2 and 3 is around a quarter turn.

However stage 2 is already quite snug and a quarter turn makes it pretty tight.

On stage 3, if you feel you've overtightened, this means you'll be damaging the bearings. Try with your stem bolts, maybe they are just slightly loose and mistaken for the play in the headset.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post

Forum Jump:

[-]
10 Latest Posts
What tools have you bought recently?
Yesterday 06:57 PM
Santini fluted frame
Yesterday 06:47 PM
Expensive bikes with crappy wheels
Yesterday 10:15 AM
Where are you from and What is your favo...
03-27-2024 11:43 PM
2007 Trek Pilot S.P.A. 5.2
03-27-2024 07:06 PM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
21 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. meamoantonio
15 posts
no avatar 4. Jesper
15 posts
no avatar 5. GirishH
15 posts