Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the new April's Giveaway for a Chance to Win the Euybike S4 Pro Max ebike worth $1299


Help with alignment of new wheels...
#1
I finally upgraded my wheels to something stronger for my 235lbs. I was previously on Bontrager SSR's and they felt so flimsy and I hated them. I bought a set of Velocity deep V's w/ 32 spoes and 105 hubs online. I swapped my old 9 sp cassette onto my new wheels which i was told were a drop in for my old wheels (spacing included). I installed them but they sit totally crooked when seated all the way down into the rear dropouts. I can loosen the the quick release and shift it so it aligns in the middle of the brake pads but when seated all the way down, it's totally crooked in the brake pads. my old wheels sat right in the middle when seated. Am I missing something here? Thanks for any help.
  Reply
#2
What type of bike do you have them on? A photo of the back of the bike would help to.
Have fun and just enjoy the ride
  Reply
#3
some pics may help, assuming your rear tringle has not been damaged. It sounds like the dish is off on your new wheel. If what you mean is that your new wheel is off center when seated in your lugs. I have seen many a new bicycle with the dish slightly off on the wheels and would dish them to the bike. A truing stand is what you need for the task. you may want to take it to the shop if you have never done this, but you would work incrementally by starting at the stem hole and loosen each spoke on the side that the rim is to far over on a 1/4 turn. then tighten the other side spokes a 1/4 turn.
mount wheel back in frame, check how even side to side and repeat til you have it. then put back in stand and give a final true to the wheel and there ya go.
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
  Reply
#4
I don't think it's dish as he said he can align by adjusting the QR.

If you ignore the pads, will the wheel mount keeping an even spacing between the chain stays behind the bottom bracket and the seat stays at the brake area?

Check the old wheel for this also.

I'm 30lbs bigger than you, & I eventually bend every frame I ride at the rear triangle (not the drop outs, the whole triangle), so that the wheel leans to the left (non-drive side) at the top, while remaining inline at the bottom bracket.

So my rear wheel is true to the direction of travel but leans to the left at the top.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
5,925
07-13-2020, 03:40 PM
Last Post: Jesper
 
11,496
02-23-2013, 01:20 PM
Last Post: Chuck
 
11,447
10-13-2012, 10:06 PM
Last Post: RobAR
 
13,411
08-21-2011, 10:05 AM
Last Post: RobAR

Forum Jump:

[-]
10 Latest Posts
Tour of Luzon 70 years of Filipino Cycli...
Today 01:22 AM
What are the best cost effective ways to...
Today 01:19 AM
RECOMMENDATION
Today 01:04 AM
Injury Recovery
Yesterday 07:33 PM
Good morning form Alberta CA
Yesterday 09:40 AM
Unlocking speed on my e-bike.
04-27-2025 01:04 PM
MTB handlebar width
04-27-2025 06:25 AM
What is your favorite MTB trail/route in...
04-27-2025 06:16 AM
Bridgestone Blouson bike.
04-26-2025 07:57 PM
Thoughts on paceline riding
04-26-2025 05:51 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
22 posts
no avatar 2. enkei
16 posts
no avatar 3. Flowrider
15 posts
no avatar 4. meamoantonio
15 posts
no avatar 5. SPINMAN
13 posts