Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


Wheel hub bearings. Room for one more ball?
#1
Hi all.

Recently my bicycles wheel hubs are showing their age and need a proper servicing.

I have stripped down both wheel hubs and was surprised to notice that I could comfortably, without any steady handed trickery, fit two more bearings in the cup for my rear wheel hub and one more bearing in the the cups of my front wheel hub.

According to the Shimano tech document my rear hub takes nine 1/4 inch ball bearings per side and the front hub takes ten 3/16 inch balls per side.

Should I stick with what Shimano is saying or should I pack the cups with as many bearings as it can comfortably take???
  Reply
#2
You did get the correct ball size? (just asking)
It is normal that 1 additional ball might fit in (though usually it would be slightly too tight). If there's really room for one additional ball (and everything can be assembled as it should, check over locknut distance and orientation of axle) I probably would put it in.
  Reply
#3
typically if original bearing were caged, add one ball
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
  Reply
#4
Nope, no caged, just loose in the cup.

I have since been advised by the LBS that it is normal for the cup to not be completely filled with bearings and to simply obide by the Shimano tech docs.
  Reply
#5
This last advice is standard for any loose ball cup and cone bearing.
DO NOT ADD EXTRA BALLS EVER over the OEM design. As others have said, a less than full fit is normal, and packing more balls in (even if they fit) screws up the bearing cone/cup geometry and ball circulation; and will lead to rapid failure. I found this out the hard way by packing an extra (25th) ball into the rh ball ring of a Sturmey Archer AW 3 speed...
cheers,
AW-hub.



(10-21-2011, 07:58 PM)d3v Wrote:  Nope, no caged, just loose in the cup.

I have since been advised by the LBS that it is normal for the cup to not be completely filled with bearings and to simply obide by the Shimano tech docs.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
3,965
02-07-2022, 02:46 PM
Last Post: Jesper
 
3,996
08-30-2021, 03:46 AM
Last Post: Poissonj1
 
21,420
05-26-2015, 02:31 PM
Last Post: eric1023
 
49,105
01-13-2015, 12:13 PM
Last Post: joseph wolf man
 
20,708
09-16-2014, 01:39 PM
Last Post: GeorgeET

Forum Jump:

[-]
10 Latest Posts
Pre Ride Food Intake
Today 02:43 AM
Post-Ride Nutrition
Today 02:40 AM
🚴‍♂️ Saddle Up for the Belgian Waffle Ri...
Yesterday 06:15 PM
Zwift v Spin v Wahoo
Yesterday 05:59 PM
Have you Ever Tried an Electric Bike?
Yesterday 05:07 PM
SAVA Explorer 6061?
Yesterday 03:31 PM
Good Morning from SW Ohio
Yesterday 07:32 AM
(So California) PV Dr to be closed to bi...
03-31-2025 09:14 PM
Tubeless vs. tubes: What are the pros an...
03-31-2025 08:28 AM
The great thing about trikes
03-31-2025 08:16 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
19 posts
no avatar 2. Flowrider
19 posts
no avatar 3. meamoantonio
12 posts
no avatar 4. Jake1
10 posts
no avatar 5. enkei
9 posts