Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the October Giveaway to Win the Qiolor TIGER Retro Electric Bike


Trueing Stand
#1
Pictures: http://s211.photobucket.com/albums/bb8/dianemisso/Stand/

I used two pieces of 3/4" aluminum angle, 1/8" thick, 14" long. One end of each needs to be cut as square as you can, the other end doesn't matter. 14" is long enough for a ISO 630 (27") wheel without tire, or a ISO 559 (26") wheel with tire. I don't know about ISO 622 (700c); as I haven't tried the Tandem's wheels yet - they are don't need any adjustment and the spoke tension is good. ISO 571 also fits with a tire installed.

Clamp the two pieces together, to form a 'T'; with the good ends matched as perfectly as you can.

Drill a hole thru the leg of the 'T' - going thru both pieces of angle. The hole should be centered approximately 5/16" from the end, and 5/16" from the bottom of the 'T' - AWAY from the "good" end. This hole needs to be enlarged to a bit over 10mm - 13/32" drill if you have one - I ended up using 1/2". It is easiest to drill use a center punch, drill a smaller hole like 1/8"; then separate the pieces to enlarge the hole.

On the front edge of the table, I screwed down a 36" x 2" x 1/8" piece of steel, for my dial indicator's magnetic base to grab on to. 2" width is about the minimum for the magnetic base. 18" would have been plenty long, but I was too lazy to cut the steel.

I used 3" angle brackets to attach the aluminum angle to the work table. #10-32 flat head screws were used to attach the brackets to the aluminum, and 1 5/8" construction screws for the brackets to the table. The first upright is screwed to the table, butted up against the steel bar. I used a blank axle with nuts jammed at the OLD for the wheel to be trued to set the spacing of the uprights before screwing the second one to the table.

Please note that this stand is not very rigid, so the you have to be gentle, and understand what on the dial indicator is the wheel out of true contribution, and what is the stand vibration/deflection contribution.

Magnetic base and dial indicator like these; but I got mine about 15 years ago - form Harbor Freight.
http://www.harborfreight.com/multipositional-magnetic-base-with-fine-adjustment-5645.html
http://www.harborfreight.com/1-inch-travel-machinists-dial-indicator-623.html

I have also added a ruler to the bottom with 0 at the center, using medium binder clips to hold it in place, and two small binder clips to help locate the rim. See:
http://s211.photobucket.com/albums/bb8/dianemisso/Nigels%20Wheels%20042311%20A/Nigels%20Wheels%20042311%20B/Nigels%20Wheels%20042311%20C/Nigels%20Wheels%20042311E/

Please note this is a reposting of information from another thread; I felt it more appropriate to put in the tools section.
Nigel
  Reply
#2
Nigel if no one ever said it you are "truly" a great engineer!!!! Smile
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#3
Very good, Nigel! We cyclist' are a creative lot, are we not!?
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
11,421
05-18-2013, 02:50 PM
Last Post: torquecyclerepairs
 
53,929
09-04-2012, 12:35 AM
Last Post: Bill
 
9,208
01-30-2012, 06:04 AM
Last Post: Joe_W
 
18,866
01-28-2012, 03:53 PM
Last Post: NewtonSquare
 
10,563
01-16-2012, 10:23 AM
Last Post: KC-Steve
 
43,748
02-06-2011, 07:56 AM
Last Post: JohnV
 
48,960
02-02-2011, 01:24 AM
Last Post: tropical
 
14,811
01-13-2011, 08:19 AM
Last Post: JohnV
 
16,180
11-02-2010, 01:47 PM
Last Post: nfmisso

Forum Jump:

[-]
10 Latest Posts
BAGGI 1936(?)
Today 10:24 AM
Do you have a four foot rule?
Today 10:10 AM
Trek domane tyre
Yesterday 05:07 PM
Greetings!
Yesterday 04:39 PM
Peugeot Nouveau Folder
Yesterday 04:34 PM
Great UK Cycle Camping Map, For E-Bikes,...
Yesterday 12:04 PM
Community Discussion Cycling Myths
11-07-2024 09:05 PM
Cycling is Anti-Aging, But There's a Cat...
11-07-2024 06:51 PM
Tasmania! Anyone ridden here?
11-07-2024 05:15 PM
Do you plan or random ride your MTB ride...
11-07-2024 05:09 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. enkei
20 posts
no avatar 2. GirishH
18 posts
no avatar 3. Jesper
18 posts
no avatar 4. Flowrider
14 posts
no avatar 5. Talha
10 posts