Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Vitesse Signal Giveaway's Winner Announced


Mixing SRAM shifters and Shimano derailleur
#1
Ok so back in November I decided to upgrade my wheelset and the rear cassette to an 8 speed from a 7 speed. So to go along with this upgrade I bought SRAM x.4 trigger shifters (Shifters). The rear derailleur I kept the same, which is a Shimano Acera (Derailleur).

Since this switch I have never been able to get it to hit all 8 of the gears. It works on the biggest gear (34 tooth) and the smallest gear (11 tooth), but in the middle it always skips gears. I've tried to adjust the cable tension, the barrel adjuster and the b-screw, but it still won't hit all the gears. Currently I have 6 of the working, but it skips 2 of them.

I've been reading around online trying to figure something out, and noticed that some people say SRAM and Shimano components aren't compatible with each other sometimes.

Anyone have any ideas? I'm open to just about everything.

Oh yeah the gear cables are only 2 months old so I'm pretty sure that's not the problem.

Thanks!
  Reply
#2
SRAM +Shimano = PAAAAAAAAAAAAAIN!!!!!!!

You my friend have been mightily lucky, normally when one mixes SRAM and Shimano in mechs and shifters the result is the mech tearing itself apart.

The reason is that they pull at different ratios of cable to movement. SRAM is 1:1, which means the length of cable pulled is the same as the distance the derallieur moves up/down the cassette. Shimano is 1:1.something, meaning the derallieur goes further for the same length of cable pulled, hence why the combination of Shimano and SRAM tears itself apart.

Put that bike away in the garage until you've replaced EITHER the rear mech or shifter so both brands are the same!

(note: you CAN mix SRAM and Shimano on the front because both pull at the same ratio, it's just the rear that's awkward).
  Reply
#3
Not sure about SRAM trigger shifters, but my hybrid came with SRAM grip shifters and both front and rear deraileurs are Shimano Altus components, including the cassette. Never had any issues with them and I've put over 1,000 miles in 6 months on that bike. Those shifters shift like a dream, sometimes better than the Tiagra components on my road bike.
HCFR Cycling Team
Ride Safe...Ride Hard...Ride Daily
  Reply
#4
SRAM do an ATTACK series of trigger shifters and grip shifters that work on the same ratio as Shimano (and are therefore compatible). That's probably what you've got, and they tend to be found on entry level mtbs, hybrids, etc. where high performance isn't as important. I'm not saying they're bad, they're actually very good for the money I think but they lack the durability of more expensive models (which is important in the world of serious MTBing).
  Reply
#5
(01-31-2011, 05:43 AM)JonB Wrote:  SRAM +Shimano = PAAAAAAAAAAAAAIN!!!!!!!

You my friend have been mightily lucky, normally when one mixes SRAM and Shimano in mechs and shifters the result is the mech tearing itself apart.

The reason is that they pull at different ratios of cable to movement. SRAM is 1:1, which means the length of cable pulled is the same as the distance the derallieur moves up/down the cassette. Shimano is 1:1.something, meaning the derallieur goes further for the same length of cable pulled, hence why the combination of Shimano and SRAM tears itself apart.

Put that bike away in the garage until you've replaced EITHER the rear mech or shifter so both brands are the same!

(note: you CAN mix SRAM and Shimano on the front because both pull at the same ratio, it's just the rear that's awkward).

Wow! I've been riding it for 3 months like that! Any idea what kind of damage I might have done to anything?

If I was to buy a new rear derailleur would this one be it SRAM X.4 Rear Derailleur Long Cage. Looks to be the one that matches my shifters and its a long cage to deal with my 3x8 gearset.
  Reply
#6
Check the rear mech for stress fractures and general damage. I don't think anything else will have broken.

That rear derallieur will be fine. Any SRAM mech with 1:1 ratios will be fine (so basically any X-series mech). You can mix and match the number in the X-series, they all work using the same system it's just the number denotes the quality (X4 being basic, X9 being ultra nice, X0 being ultra-light blingy carbon-goodness). To be honest you're better spending the money at the shifter end though as you'll notice the difference more (an x7 shifter with an x4 mech will feel a LOT nicer than an x4 shifter and an X9 mech; and is usually a cheaper combination), so just grab the X4.
  Reply
#7
(01-31-2011, 03:49 PM)JonB Wrote:  SRAM do an ATTACK series of trigger shifters and grip shifters that work on the same ratio as Shimano (and are therefore compatible). That's probably what you've got, and they tend to be found on entry level mtbs, hybrids, etc. where high performance isn't as important. I'm not saying they're bad, they're actually very good for the money I think but they lack the durability of more expensive models (which is important in the world of serious MTBing).

I guess that explains that. Smile Since I don't do MTB, I'm pretty happy with that combo on my hybrid.
HCFR Cycling Team
Ride Safe...Ride Hard...Ride Daily
  Reply
#8
JonB pretty much nailed it and I will try to make a condensed version of what he said... *deep breath*...

SRAMs X series is all dedicated to thier 1:1 pull ratio. From X.0 all the way down to X.3 and also anything with ESP as part of the model name. SRAM drlrs and shifters ONLY.

SRAM products that are Shimano compatible are any 2:1 ratio models that include MRX as part of the model name, Centera, and Attack in GripShift. The TRX trigger-shift models also work with Shimano drlrs.

The reason that your current set-up works in Hi & Low but not any other rear cogs is because the H & L Limit Screws are properly adjusted. It can't move beyond those points in either direction.
All the noise in the middle is incompatico noise.

I seriously doubt that you have done any damage beyond abusing the chain. Might consider a new one with the new drlr install.
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply
#9
Ok so I received my new rear derailleur in the mail today and installed it. My problem now is that it won't go into the highest gear (smallest one). I've tried adjusting the H limit screw, but it unscrews all the way before it lines up with the gear. Also it still skips a gear in the middle, but I figure that might be because it misses this first gear and throws it off a little. Any help would be appreciated. Thanks.
  Reply
#10
I think my thread got pushed off the new posts list when the week changed haha. Anyways I rode it in the mountains last Saturday and I could get to the lowest gear I have, but it still won't let me get into that little gear in the back. Its been raining here lately, so I haven't gotten around to playing with it to see if I could get it to work. Trying to build up some ideas for when the rain lets up, then I'll go try some out. Smile
  Reply
#11
can you use SRAM cassettes with a shimano derailleur?
  Reply
#12
i cant think of any reason why you couldnt.
Get on your bad pedalscooter and ride!
  Reply
#13
(03-04-2011, 10:22 AM)Darrenjs92ni Wrote:  can you use SRAM cassettes with a shimano derailleur?

I have a shimano cassette with a sram derailleur, and I can't think of a reason why it wouldn't work.
  Reply
#14
(03-04-2011, 02:32 PM)nameused Wrote:  
(03-04-2011, 10:22 AM)Darrenjs92ni Wrote:  can you use SRAM cassettes with a shimano derailleur?

I have a shimano cassette with a sram derailleur, and I can't think of a reason why it wouldn't work.

i was just checking, i have been using a SRAM cassette with a Shimano derailleur for a good few months now.
  Reply
#15
Unless it's XT or Ultegra, I actually prefer SRAM cassettes over Shimano, run with ANY chain, and good $$ value.
Your drlr has no clue what cass it is feeding chain to. It is the tooth profile on the cogs that gives results.
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply
#16
I'm still unable to get the chain to shift onto the smallest gear on the cassette. I adjusted the b-screw to where Alex says to in the video then tried adjusting the high limit screw but it won't move the derailleur far enough to the right to pop onto the smallest gear. Any help?
  Reply
#17
I have a Trek 7200 that I bought used , it came with SRAM Max Comp Shifters (7sp grip ) and a Shimano Acera Rear Derailleur.

The bike had a pretty rusty handlebar and cables so I decided to replace them. Also I noticed when inspecting the bike that the front derailleur was so corroded it was amazing that it worked. so I decided to replace it as well. All went fine until I installed the new rear derailleur. I can not get it to move across the gears to shift at all ! Any Ideas what I screwed up ?

I am considering putting the old rear back on as it was not in bad shape ?
  Reply
#18
(01-31-2011, 08:46 PM)RobAR Wrote:  JonB pretty much nailed it and I will try to make a condensed version of what he said... *deep breath*...

SRAMs X series is all dedicated to thier 1:1 pull ratio. From X.0 all the way down to X.3 and also anything with ESP as part of the model name. SRAM drlrs and shifters ONLY.

SRAM products that are Shimano compatible are any 2:1 ratio models that include MRX as part of the model name, Centera, and Attack in GripShift. The TRX trigger-shift models also work with Shimano drlrs.

The reason that your current set-up works in Hi & Low but not any other rear cogs is because the H & L Limit Screws are properly adjusted. It can't move beyond those points in either direction.
All the noise in the middle is incompatico noise.

I seriously doubt that you have done any damage beyond abusing the chain. Might consider a new one with the new drlr install.

(02-23-2016, 12:55 AM)budstutor Just to clarify, are twist grip and grip shift saying the same thing? and  Next, as to the MRX, Centera, and attack, are they all 2:1 ratio shifters by Sram?  Thanks. Wrote:  
(01-31-2011, 08:46 PM)RobAR Wrote:  JonB pretty much nailed it and I will try to make a condensed version of what he said... *deep breath*...

SRAMs X series is all dedicated to thier 1:1 pull ratio. From X.0 all the way down to X.3 and also anything with ESP as part of the model name. SRAM drlrs and shifters ONLY.

SRAM products that are Shimano compatible are any 2:1 ratio models that include MRX as part of the model name, Centera, and Attack in GripShift. The TRX trigger-shift models also work with Shimano drlrs.

The reason that your current set-up works in Hi & Low but not any other rear cogs is because the H & L Limit Screws are properly adjusted. It can't move beyond those points in either direction.
All the noise in the middle is incompatico noise.

I seriously doubt that you have done any damage beyond abusing the chain. Might consider a new one with the new drlr install.

Can I mix a Sram twist grip shifter with a Shimano derailleur.  Both front and back .  (3X9).  I need to replace the now installed trigger shifter for a friend who is dealing with an injured thumb and cannot put pressure on it to shift.   Left hand is injured but is considering changing both shifters to get a match and same shifting process.
I don't see too many shifters available besides Sram in a 3x9 twist grip style.  Thanks for any suggestions.
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
Happy Holidays
Today 07:25 AM
What was your favourite bicycle?
Yesterday 12:33 PM
How to Trick out your Recumbent Tadpole ...
12-20-2024 09:47 AM
How many bikes do you have now?
12-20-2024 08:24 AM
Energy gels for cycling
12-20-2024 06:53 AM
New , To me ..
12-20-2024 04:06 AM
need e-trike advice (wife knee surgery)
12-20-2024 03:58 AM
Looking for Recommendations: E-Trike for...
12-20-2024 03:55 AM
How often check or change mechanical dis...
12-20-2024 03:48 AM
Ketone Ester $$$
12-20-2024 01:54 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Alexjohnson
41 posts
no avatar 2. GirishH
24 posts
no avatar 3. Flowrider
13 posts
no avatar 4. meamoantonio
12 posts
no avatar 5. Bweighmaster
9 posts