Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the new April's Giveaway for a Chance to Win the Euybike S4 Pro Max ebike worth $1299


V Brake tension problem
#1
Hi,
I've just joined the forum and am hoping someone can give me some advice and save the remaining hair I have from being pulled out.
I have an old Raleigh mountain bike that I have given to my son, but before I did I attempted to upgrade it a little.
I have fitted new brake levers, cables and V brakes (All Clarks brand), yet I cannot get any tension in the rear brake. I have fitted the v brake and used the location hole (choice of 3) that gives the most springiness, but no joy.
I set it all up and pull the lever, but the lever will not return to its original position on its own? I have also tried puling the cable tighter at the v brake end to the extent that there is only a small amount of cable visible between the two arms and as a result little movement in the arms.

Is it faulty or am I doing something wrong

Help
Rob
  Reply
#2
Hair is a precious thing, something one should endeavor to maintain. (Sorry, I believe that it's
endeavour to you).
Compare the front brake arms to the rears & make sure the stiff wire spring arm is hooked correctly on the rear arms.
Unhook the the noodle from the brake arm so the arms pop apart.
With the spring in the center (centre to you) position:
1) Do you have "springiness" in both brake arms? If you squeeze the arms together, (simulating the brakes being applied) then suddenly let go, do they spring apart, all the way apart. in a reasonably vigorous fashion?
If they do, which I think they will, grip the brake cable (with the brake noodle still released) with your fingertips and work the brake lever. Is it difficult to return the brake lever from the cable end? You may have kinked the cable somewhere or done too tight of a turn.
Another test is to disconnect the cable at both ends and pull it back & forth with your fingertips, it should move fairly freely.

2) Did you cut the new brake cable & housing?
If you did you may have neglected to finish the housing properly after the cut, resulting in friction.
If you didn't, you may have an unacceptable amount of excess length which is curved in a manner resulting in excessive friction.

I'm sure you didn't, but please check that your brake lever purchase wasn't suited to the cantilever type, rather than the v-brake or linear pull type of brake.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
3,133
06-06-2020, 03:20 AM
Last Post: jonsio
 
Quixy
4,508
06-27-2016, 04:53 PM
Last Post: DaveM
 
8,008
08-10-2014, 01:17 PM
Last Post: cny-man
 
10,023
07-08-2013, 09:39 AM
Last Post: RBurrelli
 
15,803
06-15-2013, 10:38 PM
Last Post: Painkiller
 
48,605
02-24-2013, 12:27 AM
Last Post: adarsh

Forum Jump:

[-]
10 Latest Posts
Doctors are Prescribing Cycling
Yesterday 09:50 PM
What was your first bicycle?
Yesterday 09:17 PM
New Rider Here — Momo + Viribus = Ready ...
Yesterday 09:15 PM
The great thing about trikes
Yesterday 03:47 AM
New member old rider
04-22-2025 06:32 PM
Tubeless vs. tubes: What are the pros an...
04-22-2025 06:30 PM
Shoes for ingrown toenail
04-22-2025 05:13 PM
Good morning form Alberta CA
04-22-2025 12:24 PM
Let me introduce myself
04-22-2025 09:01 AM
Schrader vs Presta
04-22-2025 12:26 AM

[-]
Top 5 Posters This Month
no avatar 1. GirishH
24 posts
no avatar 2. SPINMAN
14 posts
no avatar 3. meamoantonio
13 posts
no avatar 4. Flowrider
13 posts
no avatar 5. enkei
11 posts