Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

Best Black Friday E-Bike Deals 2024 | Up to $1,700 in Savings

New: Take Part in the November Giveaway: Starts November 18th


Bontrager Freehub Body Removal
#1
Can anyone help me? I have managed to get my lbs to remove my Bontrager (Shimano config) free hub body from a Bontrager SSR wheel. The lbs very helpfully removed it for me as I could not locate the tool required to do the job. They have ordered a new part, but I would like to fit it myself. To do this, I need to know the tool / size needed. A 10mm allen key is not big enough. Looking down the freehub, I can see, within the body of the freehub body, a bolt that looks like a torx fitting, but I cannot establish its size, or indeed confirm it's a torx fitting. It has been suggested that a 12mm allen key will do the job. Is this correct?
  Reply
#2
Get yourself a SAE/Metric compliment size of allen key set. 12mm should do it, but if you have a set and need bigger or smaller you will have them. Cheaper to buy a set then just one.
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#3
Over the years, Bontrager has used a few designs of hubs. SSR is relatively new so, one of the two here http://www.parktool.com/blog/repair-help/freehub-service are probably what you need. If not, with more info I'm sure we can find it.
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply
#4
I have tweeted Bontrager themselves, who came back and told me I needed a 12mm wrench. I went out and purchased the wrench, and lo and behold, it doesn't fit!! Bontrager cannot even tell me their own fitting size!! The 12mm is too big, and the 10mm is too small. Logically (I know what you're thinking), an 11mm should fix it? Is this right? I am concerned that if Bontrager cannot tell me the right answer, who can?!
  Reply
#5
That narrows it down to an 11 mm, then. Any possibility that it's not the OEM hub body? And, you can't really blame Bontrager as they only 'spec' what quality requirements the hub must meet at the SSR level and don't actually manufacture it. The fixing-bolt hex size is up to the mfr and may even change during a production run, according to what they have available to keep the line running.
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply
#6
Not trying to make things confusing but if the 11mm don't do the fix then try SAE size Allen/hex wrench.
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#7
Thanks Gents. You're right in that I can't blame Bontrager. They have been very helpful in the past. I have sent back the 12mm and ordered a Park Tool 11mm. I have also found out that an 11mm is the equivalent of a 7/16" so I hopefully this will cover the imperial / metric issue. Does anyone know what the Torx size equivalent of an 11mm fitting would..........just in case??
  Reply
#8
I can assure you that it's not a Torx fitting.
Wheelies don't pop themselves. (from a QBP fortune cookie)
  Reply
#9
It's definitely an 11mm allen. I had the same issue with my Bontrager Select. The link below is from Bontragers manual.

http://www.manualslib.com/manual/19080/Bontrager-231793.html
  Reply
#10
(01-29-2013, 02:21 PM)Bdude83 Wrote:  It's definitely an 11mm allen. I had the same issue with my Bontrager Select. The link below is from Bontragers manual.

http://www.manualslib.com/manual/19080/Bontrager-231793.html

Problem solved! In fact you probably have the right size in your toolbox.

I had the same problem with my Bontrager AT650 wheel which needed an 11mm allen key to take off the Freehub body. We all know 11mm is about 7/16". Guess what size a 3/8" drive socket extension is on the male side? 7/16! So I connected the socket extension to my 3/8 drive socket wrench, inserted the male side (without any socket on it of course) into the drive side of the freewheel body and turned CCW. The freewheel body came off easily!

A few caveats. The socket extension only will grab at 4 points so be carefull you don't strip it. If your freehub does not come off easily you're gonna need to buy an 11mm allen key.

Hope this helps. Smile
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
11,931
07-31-2015, 08:34 PM
Last Post: Painkiller
 
12,037
03-11-2015, 01:21 AM
Last Post: eastman
 
13,740
02-13-2015, 01:49 PM
Last Post: nfmisso
 
16,456
01-27-2015, 03:36 PM
Last Post: nfmisso
 
13,275
11-11-2014, 12:16 AM
Last Post: cny-man
 
16,686
09-27-2014, 09:44 AM
Last Post: Painkiller

Forum Jump:

[-]
10 Latest Posts
Second wheelset for ebike.
Today 01:41 AM
Moving in Style: Beyond Regular Transpor...
Yesterday 09:23 PM
Tire Sizing (Or How to Buy A Tire)
Yesterday 12:36 PM
The Roaming Radrunner Vlog 1 Why ride ...
Yesterday 09:17 AM
Recording Bike Rides
11-20-2024 01:37 AM
Ketone Ester $$$
11-19-2024 01:04 AM
Trek domane tyre
11-18-2024 01:58 PM
Old fossil buys Ebike
11-17-2024 06:39 AM
Bike bus
11-17-2024 12:14 AM
Humber "Eiffel Safety" bike 1800s
11-16-2024 03:05 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Jesper
22 posts
no avatar 2. enkei
19 posts
no avatar 3. GirishH
14 posts
no avatar 4. ReapThaWhirlwind
11 posts
no avatar 5. Flowrider
11 posts