Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Movement in 7th and 8th sprocket
#1
Hi guys
I have a Giant M1 escape fitted with Shimano Alivio gears. The bike has done around 1600 miles on these and the vast majority on the 7th and 8th sprockets (2 smallest). Until yesterday everything was fine but when I tried cycling in top gear there was no drive at all (crank just spun and a bit clackety), though there was drive on the next lowest (7th).
On further inspection the teeth look ok, but there is play of about 2mm back and forth and side to side on both of these sprockets. Also on the very outside of the 8th - what looks to be a spacer has come loose.
The gears shift up and down fine, but wondering what can caused this and what can be done. I have another bike with a 9 speed Deore setup to hopefully transfer to the M1 if required, as the other bike is redundant.
Thanks for any help.
  Reply
#2
Check that the lockring hasn't come loose.

http://techdocs.shimano.com/media/techdocs/content/cycle/EV/bikecomponents/CS/EV-CS-HG50-8I-an-1651_v1_m56577569830728359.pdf
Ride hard or ride home alone!
  Reply
#3
It turned out that the lockring had come lose. Ive now tightned it up, regards, Phil
  Reply
#4
you should consider purchasing a new lock ring, as once it starts coming loose, it will do so again....

also note that to fit the nine speed cassette, you will also need 9 speed shifter and 9 speed chain.
Nigel
  Reply
#5
Nigel, the other bike has the shifters and chain in place, so should be ok, though Ive never acutaully done all the work before. Anything I should watch out for?
  Reply
#6
chain length - unless the two bikes have the same chainring sizes, and the rear axle to BB distance is the same, you will need to adjust the chain length. You should also plan on new cable, might not need it but.....
Nigel
  Reply
#7
(06-01-2011, 03:27 PM)cyclerUK Wrote:  Check that the lockring hasn't come loose.

http://techdocs.shimano.com/media/techdocs/content/cycle/EV/bikecomponents/CS/EV-CS-HG50-8I-an-1651_v1_m56577569830728359.pdf

I have a similar problem, but after looking at the diagram, i discovered the small gear unscrews by itself, there is no lock ring... could this be a different type of sprocket? I tightened it back up, but it still slips.

any suggestions?
  Reply
#8
it is different.

Please start a new thread, and provide all the details, and photos.
Nigel
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
4,129
06-03-2022, 08:08 PM
Last Post: Zomb13k113r
 
4,969
05-10-2020, 10:03 AM
Last Post: CharleyFarley
 
16,431
09-16-2015, 12:42 PM
Last Post: nfmisso
 
15,820
04-10-2014, 06:41 PM
Last Post: dancer
 
11,658
01-19-2014, 07:48 PM
Last Post: 1FJEF
 
16,540
04-03-2013, 12:38 AM
Last Post: DaveM
 
45,112
01-22-2013, 10:22 AM
Last Post: SimonLee
 
11,026
10-29-2012, 07:03 PM
Last Post: DaveM
 
10,275
10-06-2012, 12:00 AM
Last Post: Bill

Forum Jump:

[-]
10 Latest Posts
Santini fluted frame
Today 01:52 AM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM
Cup & Cone — Simple & Durable or PITA & ...
03-24-2024 04:53 PM
Falling back
03-24-2024 04:45 PM
Derailluer Hanger Alignment Tool
03-24-2024 02:51 PM
Chain sits on top of chainring when shif...
03-24-2024 02:41 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
20 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. GirishH
15 posts
no avatar 4. meamoantonio
15 posts
no avatar 5. Jesper
15 posts