Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take part in the August Giveaway for a brand new Street Bicycle Core Line fixed gear bike


Freewheel got louder?
#1
I have a 2008 Globe Carmel that I bought last summer. This weekend I decided that it needed a good cleaning, so I cleaned the freewheel, chain, everything I could without really taking anything apart.

Now that this is done it sounds like the freewheel(it’s a threaded one if that matters) is louder when I am not peddling(compared to before).
Is it possible that I washed dirt into it? Or is it just my imagination?

Is there any way that you could accidentally cause the clicking noise to get louder?


Thanks!
  Reply
#2
Did you use a hose? If so, how enthusiastically did you blast the bike?
It's possible that you got grit or something in it, but your cleaning could have removed the lube that the freewheel needs to run smoothly. In my opinion, the best next step is to remove the freewheel (or cassette, if you have a freehub) and lightly lubricate the moving bits, as well as checking the wheel hub bearings and chain.
  Reply
#3
(06-28-2010, 02:36 PM)Billy Wrote:  Did you use a hose? If so, how enthusiastically did you blast the bike?

Yeah I used a hose. Most likely the pressure pushed in dirt. I'll see if I can take it off. But I don't know if I have the correct tools to do it.
If I get stuck anywhere and I can't figure out what I need i'll come back and put up a pic of what it looks like. hopefully someone will be able to tell me what I need.
  Reply
#4
If you used a hose, you may have washed the grease/oil out of the freewheel mechanism, so it's now running fairly dry.

When I wash my bike, I generally use a brush with plain water, without any soap or detergent, so as to avoid dissolving any oil or grease from the places it's supposed to be.

If I do use a hose to rinse the bike after I've washed it with a brush, I avoid spraying it near the bearings in the hubs, bottom bracket and headset.

In any case, lay the bike on its side and drip some fairly thick oil in the freewheel.

If you really went to town with the hose and used a fairly high pressure jet, you might want to strip and re-grease all the bearings.
  Reply
#5
See Alex's video for removing the rear cluster: http://bikeride.com/replace-freewheel/
  Reply
#6
Taking it off won't really do much unless you're going to force grease in to it using a "freewheel buddy" or similar tool. You can drip some heavier weight oil into it at the border between the part that stays still with the wheel and the part that rotates freely. That will get some lubrication in it (though it won't really clean out any grit you got inside.)
  Reply


Forum Jump:

[-]
10 Latest Posts
Need help with info about this Evans Cyc...
Yesterday 05:21 PM
BIKEDIRECT WAITING
Yesterday 05:05 PM
One side of V brake doesn't spring back
Yesterday 02:03 PM
Back on the bike in Wales
Yesterday 01:33 PM
From Henderson Nevada
Yesterday 01:26 PM
Replacing a front derailleur
Yesterday 10:55 AM
Putting the new bike together
Yesterday 10:18 AM
clicking new chain
08-03-2020 11:48 PM
Freewheel hub wiggling in place + Chain ...
08-03-2020 08:38 PM
Where are you from and What is your favo...
08-03-2020 02:52 PM

[-]
Top 5 Posters This Month
no avatar 1. Jesper
66 posts
no avatar 2. CharleyFarley
17 posts
no avatar 3. Painkiller
15 posts
no avatar 4. RoadRacer2020
7 posts
no avatar 5. Papa Dom
7 posts