Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


What Freehub body do I have?
#1
I have a 2012 Trek 7.5 Fx Hybrid bike that I need to replace the Freehub body on the rear wheel. There are no identifying marks on this hub anywhere. The cassette that is mounted on the Freehub body is a CS-HG61-9. The gears on the cassette is 11-34 and its a 9 speed. Is there anyway to exactly identify what freebody hub this is so I can get an exact replacement?
  Reply
#2
(01-27-2015, 12:06 PM)MK86GFCS Wrote:  ...... Is there anyway to exactly identify what freebody hub this is so I can get an exact replacement?

Probably not. First remove the freehub, if it is a Shimano you need a 10mm hex key. If that is not the tool for removing it - it is not Shimano, and it may be impossible to source a replacement. If it is a Shimano, any of their "normal" 8/9/10 speed freehubs will fit.


Why do you think that you need to replace the freehub; especially on such a new bike?
Nigel
  Reply
#3
I tried a 10mm hex key and its too small by a couple of mm. It looks more like a spline in there than a hex. Guess I'm out of luck. I was replacing the cassette since the gears I use most are worn out and noticed there is a bit of slop in the freehub. I was going to take care of everything at the same time while I have it apart. Even though its a fairly a new bike I have over 15k miles on it. just normal wear and tear. Thanks
  Reply
#4
(01-27-2015, 02:09 PM)MK86GFCS Wrote:  .... a bit of slop in the freehub. .....

There is always a bit of slop in freehubs, has to be or they would not work. As long as the pawls feel good, and are not making too much noise, leave it.

A little bit of light machine oil helps the pawls, but can hurt the bearings.

Kind of reminds me of the story about when Rolls Royce licensed GM's Turbohydramatic automatic transmission in the late 1950's. The ones GM built worked very well; the first ones RR built would not transmit any torque - the cars would not move. Turns out RR polished everything inside to a bright smooth finish - just like the visible portions of their cars. The torque converter rotor and stator have to be be rough for the fluid to transmit torque......
Nigel
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
3,235
10-01-2022, 05:13 AM
Last Post: Jesper
 
12,426
07-31-2015, 08:34 PM
Last Post: Painkiller
 
60,480
07-14-2013, 05:27 PM
Last Post: Gixxer
 
21,927
05-23-2013, 11:21 AM
Last Post: mmontero
 
10,447
05-08-2013, 11:09 PM
Last Post: nfmisso

Forum Jump:

[-]
10 Latest Posts
Post-Ride Nutrition
Today 02:06 AM
🚴‍♂️ Saddle Up for the Belgian Waffle Ri...
Today 02:03 AM
Pre Ride Food Intake
Today 12:14 AM
SAVA Explorer 6061?
Yesterday 03:31 PM
braking by reversing the pedals
Yesterday 01:00 PM
Zwift v Spin v Wahoo
04-01-2025 05:59 PM
Have you Ever Tried an Electric Bike?
04-01-2025 05:07 PM
Good Morning from SW Ohio
04-01-2025 07:32 AM
(So California) PV Dr to be closed to bi...
03-31-2025 09:14 PM
Tubeless vs. tubes: What are the pros an...
03-31-2025 08:28 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
22 posts
no avatar 2. Flowrider
19 posts
no avatar 3. meamoantonio
12 posts
no avatar 4. Jake1
11 posts
no avatar 5. enkei
9 posts