Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the new April's Giveaway for a Chance to Win the Euybike S4 Pro Max ebike worth $1299


First real project
#1
So I have started the process to build a MTB from the frame up as a side project from second handish parts. Mainly because I want to learn and I love tinkering with stuff.

I have a great fork and an amazing frame. I know for a fact I need to have a headset installed but in I'm just not sure how to measure them to make sure they fit.

Just a few questions, and I apologize if these have already been answered I did not see anything in my searches.
1. Am I correct in thinking that the inner diameter of the crown barring needs to be super snug on the steerer tube?
2. What numbers are important when fitting a headset? (what should I be looking for or not worrying about number wise )

Thanks in advance,
Ryan
  Reply
#2
(04-07-2011, 10:50 PM)rpalmertree Wrote:  ...<snip>...

1. Am I correct in thinking that the inner diameter of the crown barring needs to be super snug on the steerer tube?
2. What numbers are important when fitting a headset? (wht should I be looking for or not worrying about number wise )
...<snip>...
Hi Ryan;

First; do you have a threaded or threadless headset?

If threadless:
1. no; the bearings should be very loose on the head tube - loose balls even if you have the patience to install them - you can fit more balls without the retainer, thus resulting in significantly stiffer headset. The balls (with or without a retainer) end up have angular contact between two surfaces.
[Image: k_a2_1_e.gif]
The image above shows a commercial ball bearing (aka sealed bearing as used in higher end hubs and cranksets). In the heads set, both the inner and outer races have a single land - they are often replaceable, and always hard steel alloy.

2. decide on loose balls, or balls in a retainer.

If you have a threadless headset things are a bit different.

http://www.sheldonbrown.com/headsets.html
Nigel
  Reply
#3
Hey Nigel, thanks for the response!

The headset needs to be pressed in so threadless. I think the BBB said something like .1 to .25 is acceptable tolerances for a press fit.

So if my head tube was 33.4mm I would need to find a headset that was around 33.3mm - 33.1mm?

I'll checkout what Sheldon says today thanks for link!

Thanks,
Ryan
  Reply
#4
(04-07-2011, 11:18 PM)nfmisso Wrote:  
(04-07-2011, 10:50 PM)rpalmertree Wrote:  ...<snip>...

1. Am I correct in thinking that the inner diameter of the crown barring needs to be super snug on the steerer tube?
2. What numbers are important when fitting a headset? (wht should I be looking for or not worrying about number wise )
...<snip>...
Hi Ryan;

First; do you have a threaded or threadless headset?

If threaded: oops !!!!!
1. no; the bearings should be very loose on the head tube - loose balls even if you have the patience to install them - you can fit more balls without the retainer, thus resulting in significantly stiffer headset. The balls (with or without a retainer) end up have angular contact between two surfaces.
[Image: k_a2_1_e.gif]
The image above shows a commercial ball bearing (aka sealed bearing as used in higher end hubs and cranksets). In the heads set, both the inner and outer races have a single land - they are often replaceable, and always hard steel alloy.

2. decide on loose balls, or balls in a retainer.

If you have a threadless headset things are a bit different.

http://www.sheldonbrown.com/headsets.html

sorry about that, should have gone to bed instead of responding.
Nigel
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
17,554
11-30-2023, 10:33 AM
Last Post: Talha
 
10,938
01-09-2016, 01:19 AM
Last Post: Bill
 
18,379
01-01-2015, 05:20 PM
Last Post: elmore leonard
 
8,199
11-04-2013, 02:14 PM
Last Post: DaveM
 
5,534
06-23-2013, 11:20 PM
Last Post: FredS
 
67,985
07-09-2012, 01:06 AM
Last Post: jeracravo
 
11,483
02-21-2011, 01:56 PM
Last Post: eorta7

Forum Jump:

[-]
10 Latest Posts
1987 Tommaso Alloy lugged frame
Today 11:18 AM
Injury Recovery
Today 08:20 AM
RECOMMENDATION
Yesterday 04:24 PM
New Member
Yesterday 03:31 PM
2011 GT Tachyon upgrade/mod
Yesterday 08:45 AM
Doctors are Prescribing Cycling
04-23-2025 09:50 PM
What was your first bicycle?
04-23-2025 09:17 PM
New Rider Here — Momo + Viribus = Ready ...
04-23-2025 09:15 PM
The great thing about trikes
04-23-2025 03:47 AM
New member old rider
04-22-2025 06:32 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
24 posts
no avatar 2. SPINMAN
14 posts
no avatar 3. meamoantonio
13 posts
no avatar 4. Flowrider
12 posts
no avatar 5. enkei
11 posts