Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


Chain skip
#1
I've  a 9speed DA that is fine going up & down the gearing, but put a load on 1st, 2nd & sometime, the chain skips. I cannot get my indexing right to get rid of it, any thoughts?
  Reply
#2
Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.
  Reply
#3
(10-09-2015, 12:42 PM)DaveM Wrote:  Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.

+1

Other possibilities (less likely):
* a stiff link in the chain.
* inadequate chain lubrication.
* weak RD spring.
* chain too long.
Nigel
  Reply
#4
(10-09-2015, 02:19 PM)nfmisso Wrote:  
(10-09-2015, 12:42 PM)DaveM Wrote:  Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.

+1

Other possibilities (less likely):
* a stiff link in the chain.
* inadequate chain lubrication.
* weak RD spring.
* chain too long.

Chain is new. Likely i didnt cut the length correctly, first time using a removable link chain. Or it is the cassete, it has about 3k mileson it?
  Reply
#5
Check the length first. But putting a new chain on an old cassette (even one without that many miles) is a very typical cause of the sudden appearance of chain skip under load. Chains and cassettes "wear into each other" and it's common to have problems when you change one but not the other.
  Reply
#6
(10-08-2015, 08:38 PM)mastermartymo Wrote:  I've  a 9speed DA that is fine going up & down the gearing, but put a load on 1st, 2nd & sometime, the chain skips. I cannot get my indexing right to get rid of it, any thoughts?

Maybe a dumb question but are you using a 9 speed chain? They are different then a ten 8 speed chain I'm told. Slightly thinner I believe.
"Where ever we go, there we are"
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
15,633
04-04-2013, 10:44 PM
Last Post: larsonian
 
14,380
05-13-2012, 03:48 PM
Last Post: Joe_W
 
11,150
07-18-2011, 04:42 AM
Last Post: Joe_W
 
8,697
10-28-2008, 10:42 PM
Last Post: Alex Ramon

Forum Jump:

[-]
10 Latest Posts
Doctors are Prescribing Cycling
Yesterday 09:31 PM
How to improve cycling endurance? I've h...
Yesterday 06:27 PM
Hot Weather Safety
Yesterday 06:05 PM
Variation in Conti GP5000 sizing?
Yesterday 05:42 PM
Budget Gravel Bikes - useful YouTube vid...
Yesterday 03:43 PM
Continued learnings from bikepacking
Yesterday 08:37 AM
Cleats idea. What do you think?
Yesterday 08:28 AM
Has anyone tried one of these portable e...
Yesterday 06:43 AM
2007 Trek Pilot S.P.A. 5.2
06-29-2025 09:08 PM
First long distance ride..
06-29-2025 09:45 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
21 posts
no avatar 2. Flowrider
19 posts
no avatar 3. meamoantonio
13 posts
no avatar 4. rydabent
12 posts
no avatar 5. enkei
10 posts