Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

Best Black Friday E-Bike Deals 2024 | Up to $1,700 in Savings

New: Take Part in the November Giveaway: Starts November 18th


7 broken spokes later... grabbing freehub !!
#21
I checked all my bike wheels, including the road bikes(700c) and they have 2.0 spokes on all of them. I haven't had any trouble with them(nocking on wood). It has got to be just cheap spokes and a better quality spoke should do the trick along with the next size up, right??
What do you guys think??
There's no way I'm going to be able to afford to spend $200+ on a rear wheel build per bike... I'll just have to start walking or keep ordering from amazon like 1FJEF said.

For 135mm: Wheelmaster 40H hub, Velocity Aeroheat 26" 40 h Blk Ano/Sil Sided rim, Wheelsmith SS14 spokes 252 (non drive) and 250 (drive side) mm, Wheelsmith 12mm nickel plated brass nipples.
[/quote]

How much??
  Reply
#22
For 135mm: Wheelmaster 40H hub, Velocity Aeroheat 26" 40 h Blk Ano/Sil Sided rim, Wheelsmith SS14 spokes 252 (non drive) and 250 (drive side) mm, Wheelsmith 12mm nickel plated brass nipples.
[/quote]

Where do you get this at??
  Reply
#23
Thanks guys for the help !!
  Reply
#24
(11-05-2013, 12:01 AM)!TREK4ME! Wrote:  For 135mm: Wheelmaster 40H hub, Velocity Aeroheat 26" 40 h Blk Ano/Sil Sided rim, Wheelsmith SS14 spokes 252 (non drive) and 250 (drive side) mm, Wheelsmith 12mm nickel plated brass nipples.

Where do you get this at??
parts from Amazon, then build. This is now my standard recipe for 559 rear wheels, for 622, substitute Velocity Dyad rims (same extrusion) and longer spokes. We have the 622 on our T50 tandem. The Dyad rims were so much faster to build and true than all the other rims that I have tried that I am going use them only in the future.

SS14 spokes are 2.0mm in diameter. (about $25 for 50 on Amazon)

DH13 spokes are 2.3mm in diameter near the bend and 2.0mm for the rest. (harder to find, usually around $55 for 36)

Please note that the MOST important thing is the quality of the build - high tension, stress relief - results in a very long lasting wheel, the quality of the spokes are secondary. That said, I use Wheelsmith spokes exclusively - they have a 'W' on the ends.
Nigel
  Reply
#25
Awesome !!... Thanks Nigel !!!
  Reply
#26
Just an update...
I took the plunge and replaced the spokes on the wheel that kept breaking spokes. I'm addicted.... took a lot of patience, but it looks like I licked it. Rode 40 miles on the relaced wheel and no broken spokes. Whew !!!!!
I'm not sure what spoke brand I used, but they have a "N" on the hub end. Took these spokes from a wheel I had laying around that I was saving the hub for. The rim was toast, so I decided to use the spokes.
I'm ready to try my 700c spoke relacing, now...
Thanks again for all the help !!!,
PJ
  Reply
#27
Hm... reusing spokes is a bit of a difficult point. I would probably not do it, as I am not sure how well it was built and where it has been. There are many wheelbuilders who will only reuse spokes from their own builds. Maybe Nigel can chime in with some metallurgical / mechanical comments.

That said:
Congratulations! Looks like we've got a new addict here... though I have to admit I just bought a new pair of wheels *blushes*
  Reply
#28
I have only once re-used spokes; transferred the DH13 from the drive side to the non-drive side, and put new DH13 on the drive side.

Normally, if I am rebuilding a wheel, I just cut all the spokes.
Nigel
  Reply
#29
You don't want a solvent in the freewheel.. hard to completely drain it.. meaning that remainder raises heck with whatever light oil applied as a followup.

Run a good dose of liquid wrench in... give it a few spins. Let it sit... will solve most all stubborn screw on's.

Liquid wrench.. also is one of the best chain lubes.. by miles. Best applied after the ride.. let it soak in. Lubes the pins.. prevents them from rusting. Chains last MUCH longer. Chain lubes are a marketing game.. just like the majority of bike component selling.

The spoke breakage mantra is just that.. often true.. often not. Often spokes break due to NO maintenance.. some go loose and the cascading loss of tension effect breaks them. Left side rears are the main culprit. IF you stay with traditional lacing forms... get ALL the NDS rear above 60 kgf.. all of them. Or glue the nipples with locker or after the build. 60 kgf normally is above the 'they'll shake loose zone'.. which starts the trouble issues.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
7,643
05-09-2023, 08:07 AM
Last Post: ichitan
 
11,931
07-31-2015, 08:34 PM
Last Post: Painkiller
 
16,456
01-27-2015, 03:36 PM
Last Post: nfmisso
 
9,994
07-24-2014, 06:20 PM
Last Post: nfmisso
 
12,217
01-21-2014, 04:48 PM
Last Post: 1FJEF
 
20,972
05-23-2013, 11:21 AM
Last Post: mmontero

Forum Jump:

[-]
10 Latest Posts
Second wheelset for ebike.
Today 01:41 AM
Moving in Style: Beyond Regular Transpor...
Yesterday 09:23 PM
Tire Sizing (Or How to Buy A Tire)
Yesterday 12:36 PM
The Roaming Radrunner Vlog 1 Why ride ...
Yesterday 09:17 AM
Recording Bike Rides
11-20-2024 01:37 AM
Ketone Ester $$$
11-19-2024 01:04 AM
Trek domane tyre
11-18-2024 01:58 PM
Old fossil buys Ebike
11-17-2024 06:39 AM
Bike bus
11-17-2024 12:14 AM
Humber "Eiffel Safety" bike 1800s
11-16-2024 03:05 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Jesper
22 posts
no avatar 2. enkei
19 posts
no avatar 3. GirishH
14 posts
no avatar 4. Flowrider
11 posts
no avatar 5. ReapThaWhirlwind
11 posts