Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

Best Black Friday E-Bike Deals 2024 | Up to $1,700 in Savings

New: Take Part in the November Giveaway: Starts November 18th


Unable to loosen and remove.
#1
hey,

I've recently been renovating a bike that has been sitting in my garden for quite some time. On a closer inspection I could see that some of the welds had warn and that the stem had bent. I removed the bolt from the top of the handle bars and was unable to remove the handle bars. Knowing that I didn't need the stem I resorted to sawing it in half,

[Image: kWY3Zaz.jpg?1]

I then found another set of handle bars and forks on another bike that are the same size as the ones I had sawn off, so I cut them from the other bike,

[img][Image: 7MWRx74.jpg][/img]

I went to remove the handle bars to slot the stem through my bike frame but yet I am faced with the same problem. I've removed the allen bolt from the top of the handle bars and loosened the nuts on the stem but I cant remove the handlebars,

[Image: 7VZ0ahl.jpg]

I honestly don't know what to do... :/
[/font]
  Reply
#2
Put the bolt back in, screw down so that there is 3mm (1/8") clearance under the head of the bolt, place a block of wood on top of the bolt, then wack the block of wood with a mallet, until the clearance the head of the bolt is zero or the handle bars are loose. Repeat as required.

Turning the whole thing upside down, and pouring in penetrating oil, and letting sit over night before doing the above is not a bad idea.
Nigel
  Reply
#3
Thanks. Its dark out now but I'll give it a try tomorrowSmile
  Reply
#4
I'm not 100% sure now this is going to work tho, if I'm trying to loosen them and pull them out to then fit the forks and bars onto my bike. How is hammering the bolt back in going to help me achieve this?
  Reply
#5
Here is a link to how steering stems work. The bolt pulls the wedge up, as Nigel said put the bolt back in screw it into the wedge, leave a bout a 1/4" out and than tap with hammer to drive the wedge down. Put some penetrating oil by holding the bike or the forks upside down first.

Scroll halfway down to diagram.........

http://sheldonbrown.com/gloss_st-z.html#stem
Never Give Up!!!
  Reply
#6
right, I get it. I'll give it a bash tomorrow then. Pun intended.
  Reply
#7
Thanks for the help guys. What you told me to do work Smile. If I run into any other problems I'll post again.
  Reply
#8
Just curious, why did you cut the head tube off the other frame? Was the frame any good? It isn't now...
Craig Domingue - East Texas Hick
  Reply
#9
I didn't need the bike so...
  Reply
#10
Well, I guess that's one way to work on a bike.
Craig Domingue - East Texas Hick
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
Moving in Style: Beyond Regular Transpor...
Today 07:43 AM
Second wheelset for ebike.
Today 01:41 AM
Tire Sizing (Or How to Buy A Tire)
Yesterday 12:36 PM
The Roaming Radrunner Vlog 1 Why ride ...
Yesterday 09:17 AM
Recording Bike Rides
11-20-2024 01:37 AM
Ketone Ester $$$
11-19-2024 01:04 AM
Trek domane tyre
11-18-2024 01:58 PM
Old fossil buys Ebike
11-17-2024 06:39 AM
Bike bus
11-17-2024 12:14 AM
Humber "Eiffel Safety" bike 1800s
11-16-2024 03:05 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Jesper
22 posts
no avatar 2. enkei
19 posts
no avatar 3. GirishH
14 posts
no avatar 4. ReapThaWhirlwind
11 posts
no avatar 5. Flowrider
11 posts