Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the new April's Giveaway for a Chance to Win the Euybike S4 Pro Max ebike worth $1299


Chain Replacement -- Much Shorter than Original
#1
Hello,

I am replacing my chain for the first time on this (or any for that matter) bike. I followed the tutorial provided here (running it around both large sprockets), however, when I compare the new chain length to the original one that was on the bike, I find that the new one is quite a bit shorter.

5 or 6 (can't quite remember) complete links short. I didn't necessarily expect them to be the same length, but that seems quite a big difference.

Is this common? The original chain is the one that the bike came with. I double checked my measurement and everything is correct. The chain doesn't look to short (I can run it through the deraillers and sprockets no problem).

How could the bike operate with such a big difference in chain length? A link here or there difference I can understand, but a 5" difference is a lot.

Thanks,
  Reply
#2
wow; that is a lot. If it will shift smoothly on to the largest sprockets front and rear at the same time, then it is the correct length.

Has the freewheel or cranks been changed on the bike?

Sometimes there are quality issues at manufacturers.
Nigel
  Reply
#3
Hi Nigel,

I replaced the "freewheel" at the same time as I replaced the chain, but I replaced it with the same "Shimano" freewheel as the original one.

But I can shift to and from the large / large combo without a problem.

One thing I did notice, was that the derailler pulley thing (not sure of the correct name), is much closer to the "freewheel" than before. It's not touching it, but it is *very* close.

Would that be due to a shorter chain?

Hugh
  Reply
#4
Hi Hugh;

Derailleur closeness to the freewheel is also affected the "B" screw adjustment - assuming Shimano or similar derailleur.

I believe that everything is fine, given you followed the instructions, and the system is operating smoothly.
Nigel
  Reply
#5
Thanks Nigel. I have adjusted the "B" screw, but I can't get anywhere close to the range that I had before. I rode into work today for the first time and everything seems fine, but I was just surprised at how close the distance is between the two.

Hugh,
  Reply
#6
Hi Hugh;

The closer the derailleur is to the cogs, the quicker it will shift. Perfect is getting it as close a possible without touching. Sounds like your bike should be operating better than before.
Nigel
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
5,435
07-18-2020, 05:18 AM
Last Post: Jesper
 
10,634
03-30-2013, 12:02 PM
Last Post: 1FJEF
 
25,922
09-07-2011, 05:16 PM
Last Post: DaveM
 
12,385
09-10-2010, 09:58 AM
Last Post: ezdoesit
 
11,768
04-21-2010, 08:36 PM
Last Post: GeorgeET

Forum Jump:

[-]
10 Latest Posts
What are the best cost effective ways to...
Today 02:58 PM
Good morning form Alberta CA
Today 10:35 AM
Injury Recovery
Today 10:29 AM
Front derailer not moving
Today 08:40 AM
RECOMMENDATION
Today 07:35 AM
Looking for Recommendations: E-Trike for...
Today 04:11 AM
need e-trike advice (wife knee surgery)
Today 04:08 AM
Tour of Luzon 70 years of Filipino Cycli...
Yesterday 01:22 AM
Unlocking speed on my e-bike.
04-27-2025 01:04 PM
MTB handlebar width
04-27-2025 06:25 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Flowrider
16 posts
no avatar 2. enkei
16 posts
no avatar 3. Painkiller
15 posts
no avatar 4. meamoantonio
15 posts
no avatar 5. GirishH
14 posts