Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


Hydraulic discs rubbing, is that ok?
#1
Hi everyone. New to the forums, and am excited to learn a lot about maintenance from you all! When I transport my bike in my car, I have to take off the front wheel and put a spacer in between the pads. Recently, I forgot to put the spacer in and accidentally pulled the brake ever so slightly. Now the inside brake pad (i.e. the one closest to the frame) is rubbing just a bit when I spin the front wheel, but the outside pad is fine. I can see light through the inside gap just a bit, so it looks as if wear on the pad will alleviate the problem. I took my bike in to a shop, and they told me to 'ride the hell out of it' and the pad will wear down.

My question is this: is that a good idea? Will riding with the slight rub of the pad hurt my brake system or rotors? Thanks for your help everyone!
  Reply
#2
It will generate unnecessary heat, but wont really hurt anything. I have to recenter my disc brakes all the time because of various reasons. Typical method is to take off your wheel and loosen the bolts holding the caliper to the adapter bracket on your fork, and spread the brake pads with a spreader. A flat head screw driver can work if you're careful, but you can gouge your pads pretty easily. If you do, you can take them out and smooth them on a piece of sand paper lying on a flat surface. The spacer you have will probably do the trick better than a screwdriver. Anyway, you're basically pushing the brake drums back into the caliper to get more space between the pads. Once they're spread, but the wheel back on, and then squeeze the brake lever hard 5 or 6 times. Then squeeze the snot out of it and snug up the caliper bolts again. When you let go of the lever the disc should be centered between the pads again. Spin the wheel to be sure (redo the bolt snugging process and the hard brake pull if it's not), and then you can tighten up the bolts to their recommended torque value (usually 7 N-m, if memory serves). I've found that just taking off the wheel and putting it back into the dropouts can screw up the disc alignment, though. You can sometimes correct the problem buy pulling on the quick release lever, wiggling the wheel, and tightening it back up.

Good luck!

-Dave
  Reply
#3
(08-29-2010, 07:52 PM)dave_sd Wrote:  It will generate unnecessary heat, but wont really hurt anything. I have to recenter my disc brakes all the time because of various reasons. Typical method is to take off your wheel and loosen the bolts holding the caliper to the adapter bracket on your fork, and spread the brake pads with a spreader. A flat head screw driver can work if you're careful, but you can gouge your pads pretty easily. If you do, you can take them out and smooth them on a piece of sand paper lying on a flat surface. The spacer you have will probably do the trick better than a screwdriver. Anyway, you're basically pushing the brake drums back into the caliper to get more space between the pads. Once they're spread, but the wheel back on, and then squeeze the brake lever hard 5 or 6 times. Then squeeze the snot out of it and snug up the caliper bolts again. When you let go of the lever the disc should be centered between the pads again. Spin the wheel to be sure (redo the bolt snugging process and the hard brake pull if it's not), and then you can tighten up the bolts to their recommended torque value (usually 7 N-m, if memory serves). I've found that just taking off the wheel and putting it back into the dropouts can screw up the disc alignment, though. You can sometimes correct the problem buy pulling on the quick release lever, wiggling the wheel, and tightening it back up.

Good luck!

-Dave

I read on another post to try business cards, I think I'll give that a try. The rub is BARELY there, I can even see light for the bottom 3/4 of the pad. But as you say, even without messing with it, it should be fine to ride.
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
SAVA Explorer 6061?
Today 03:31 PM
braking by reversing the pedals
Today 01:00 PM
Pre Ride Food Intake
Today 02:43 AM
Post-Ride Nutrition
Today 02:40 AM
🚴‍♂️ Saddle Up for the Belgian Waffle Ri...
Yesterday 06:15 PM
Zwift v Spin v Wahoo
Yesterday 05:59 PM
Have you Ever Tried an Electric Bike?
Yesterday 05:07 PM
Good Morning from SW Ohio
Yesterday 07:32 AM
(So California) PV Dr to be closed to bi...
03-31-2025 09:14 PM
Tubeless vs. tubes: What are the pros an...
03-31-2025 08:28 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
19 posts
no avatar 2. Flowrider
19 posts
no avatar 3. meamoantonio
12 posts
no avatar 4. Jake1
11 posts
no avatar 5. enkei
9 posts