Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


Sturmey Archer
#1
Where can I find anti rotational washer for Sturmey Archer 8sp hub that will fit vertical dropdown ,as Sturmey Archer does not make these. Mounted hub to a Terra Trike Tour. Made a set (not pretty but working so far,)
  Reply
#2
I'd say your best bet is eBay, then I'd start hitting all the bike shops. In Gainesville there are two shops that specialize in used bikes and have bins full of spare parts. If there is something similar in your area, that'd be the place to go.
  Reply
#3
(11-12-2011, 04:02 PM)rwstacey Wrote:  Where can I find anti rotational washer for Sturmey Archer 8sp hub that will fit vertical dropdown ,as Sturmey Archer does not make these. Mounted hub to a Terra Trike Tour. Made a set (not pretty but working so far,)

It is highly unlikely that you will find anything ready made, because horizontal dropouts are needed to adjust the chain tension with these and similar non-derailleur equipped hubs. SRAM might have something for their combo IGH/Cassette hub.

Question - how do adjust the chain tension?
Nigel
  Reply
#4
(11-15-2011, 12:41 AM)nfmisso Wrote:  
(11-12-2011, 04:02 PM)rwstacey Wrote:  Where can I find anti rotational washer for Sturmey Archer 8sp hub that will fit vertical dropdown ,as Sturmey Archer does not make these. Mounted hub to a Terra Trike Tour. Made a set (not pretty but working so far,)

It is highly unlikely that you will find anything ready made, because horizontal dropouts are needed to adjust the chain tension with these and similar non-derailleur equipped hubs. SRAM might have something for their combo IGH/Cassette hub.

Question - how do adjust the chain tension?

Sorry for not replying sooner;
As for the washers I have ended up making a set out of 1" angle iron (drill,files and a hacksaw and a lot of patience) Have almost a 1000 miles on it so far no problems. As for chain tension Sturmey Archer has tensioner or Utah Trikes. With the Terra Trike Tour having a rear floating idlers I added a shim and lined right up. Now in the process of adding a Patterson Drive with a power Idler setup.
  Reply
#5
I rebuilt a 1955 AW, and I can't get 1st to work. I have a bunch of NOS clutch springs of two gauges, and when I use the finer gauge springs 1st doesn't engage -- it just freewheels, but when I use the heavier gauge, stronger, spring, I can't get the lever past second. I have tried several of each type of spring, and this is very consistent. Second and third gears work fine. Any ideas?
Thanks,
Jeff
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
1,311
09-01-2024, 03:20 AM
Last Post: Talha
 
41,327
10-06-2014, 12:41 PM
Last Post: DaveM
 
10,599
03-23-2012, 04:51 PM
Last Post: trevgbb
 
14,079
01-18-2011, 04:05 PM
Last Post: momule

Forum Jump:

[-]
10 Latest Posts
Peugeot Nouveau Folder
Today 05:24 PM
Frame Material Trade-offs: 5 Years of Da...
Today 05:20 PM
Best way to thoroughly clean a chain?
Today 05:13 PM
The great thing about trikes
Today 12:11 PM
CALLING UK CYCLISTS! - Take Action to Fu...
02-19-2025 08:25 AM
Club Rides
02-17-2025 09:24 AM
eBikes are banned in these places!
02-17-2025 09:21 AM
Tubeless vs. tubes: What are the pros an...
02-16-2025 07:07 PM
What are the pros and cons of clip-on pe...
02-16-2025 06:55 PM
Where to travel on a bike Bucket List.
02-16-2025 10:33 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Flowrider
17 posts
no avatar 2. meamoantonio
15 posts
no avatar 3. enkei
14 posts
no avatar 4. GirishH
13 posts
no avatar 5. rydabent
8 posts