Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the January Giveaway for a Chance to Win the Movcan V80 E-bike Worth $889


Installing a new bottom bracket.
#1
Ok so I finally got my bottom bracket (sealed bearing) in the mail. During the time I've been waiting for it, I've been looking up how I should grease the threads and any ways to make a good seal for it. What I got from my research was that I should wrap the threads with teflon tape and then grease both the cups and the threads on the bike when installing it. However when I got the bottom bracket in the mail it has a plastic cup on the end and it says not to apply grease to it. I don't think it would make much of a difference if I grease it or not.

So my question is should I use the teflon tape and what should I grease when installing the bottom bracket?

Thanks!
  Reply
#2
No Teflon. You can grease the threads but its plastic so its not gonna be so critical. That plastic cup will torque itself on there and corrosion shouldn't be such a factor with plastic threading onto a aluminum(assuming aluminum) thread. Just use proper torque which should be included with the new BB instructions. Always a good idea to chase threads of the BB shell to ensure good clean threads. Happy installation...
GO RIDE...
  Reply
#3
Yeah my frame is aluminum.
I might have found a problem. When I pulled off my old BB, there was water sitting in there. Any ideas where this came from and if its any problem?
  Reply
#4
Be very careful with plastic cups, it is very easy to ruin the splines if over torquing, and if they say no grease on the plastic, they probably mean it.
Also doubt if there is room for tape in the threads as they are usually a tight fit and could interfere with assembly.
Water ingress, most BB's, and I see now head sets, usually have some sort of sealing which is semi effective unless very aggressive conditions,
but down the seat tube if a hardtail is possible.
Or do you use a power washer, no. no.
  Reply
#5
(11-06-2010, 04:34 AM)trevgbb Wrote:  Be very careful with plastic cups, it is very easy to ruin the splines if over torquing, and if they say no grease on the plastic, they probably mean it.
Also doubt if there is room for tape in the threads as they are usually a tight fit and could interfere with assembly.
Water ingress, most BB's, and I see now head sets, usually have some sort of sealing which is semi effective unless very aggressive conditions,
but down the seat tube if a hardtail is possible.
Or do you use a power washer, no. no.

I don't put it through any aggressive conditions. It just lives its life outside and gets hit with Hawaiian rain. I do have a hardtail, so that might be possible. And nope, no power washer for me Tongue
  Reply
#6
Finding water in the BB shell is common. Possibly coming from seat post and the wet environment.
GO RIDE...
  Reply
#7
(11-06-2010, 11:59 PM)JohnnyCO Wrote:  Finding water in the BB shell is common. Possibly coming from seat post and the wet environment.

Well I decided to look at my seat post today and there is no hole in the top. There is a small slot where the seat post clamp is, so maybe it gets in there.
  Reply
#8
its very hard to waterproof anything completely. this is why its important to tear down and relube things regularly. contrary to what the assemblers at walmart think, grease is cheap.
Get on your bad pedalscooter and ride!
  Reply
#9
China-Mart says, "after this bike breaks cause you can't fix anything on one, time for your NEXT bike."
GO RIDE...
  Reply
#10
(11-07-2010, 02:34 PM)JohnnyCO Wrote:  China-Mart says, "after this bike breaks cause you can't fix anything on one, time for your NEXT bike."

Too bad its a Trek not a Next. But still pretty funny, I might say that to people with those walmart bikes now
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
The Roaming Radrunner Vlog 1 Why ride ...
Today 11:57 AM
What was your first bicycle?
Today 07:38 AM
How many bikes do you have now?
Yesterday 03:27 PM
Newbie from , Texas
Yesterday 02:41 PM
Operation of Santa Monica Ebike
Yesterday 01:20 PM
Cycling industry is pricing out their ow...
Yesterday 06:40 AM
What are the best maintenance practices ...
Yesterday 06:34 AM
What jockey wheel Red 10 Speed
01-10-2025 02:32 AM
Club Rides
01-09-2025 02:22 PM
Gears and derailleur misalignment
01-09-2025 02:15 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
24 posts
no avatar 2. enkei
18 posts
no avatar 3. meamoantonio
11 posts
no avatar 4. ReapThaWhirlwind
8 posts
no avatar 5. Painkiller
7 posts