Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Vitesse Signal Giveaway's Winner Announced


SRAM rival
#1
Hi
I'm new to SRAM and am just setting up my road bike with SRAM Rival. However, it takes a lot of force to move the shift lever to get 19/21/23 sprockets.

Any suggestions

Thanks for any help
  Reply
#2
Im no expert on those, but does the shifter have a adjustment screw that may have been tighten too much?
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#3
(01-20-2010, 09:12 AM)Turborider Wrote:  Hi
I'm new to SRAM and am just setting up my road bike with SRAM Rival. However, it takes a lot of force to move the shift lever to get 19/21/23 sprockets.

Any suggestions

Thanks for any help

What kind of shifter do you have can you post a pic of it?
My dad always told me a Sledge a matic can fix any thing.
  Reply
#4
Hi
Thanks for the suggestions

The shifters are SRAM Rival as well and don't appear to have any adjustments
  Reply
#5
Ok since they are newer I am sure you have this manual..
http://www.sram.com/_media/techdocs/roadshifters_IBS_ForceRival__12_06.pdf

Are you talking about the front derailler? If so..

As I was reading the only thing I came across was this little excerpt, " The left hand shifter offers a trim function for the front derailleur to
allow the chain running smoothly on the small chainring in extreme
positions. (Shift position 1 and 2 is for the small chainring. Shift position
3 is for the large chainring.) " Also make sure the front derailler is properly aligned watch Alex's Video on front derailler adjustment http://bikeride.com/adjust-front-derailer/ .

If you are talking about the rear "sprockets"/ derailler then..
Here is the manual for the rear Derailler that I assume is SRAM Rival as well...
http://www.sram.com/_media/techdocs/roadrearderailleurs_ForceRival__1_06.pdf
there is a part in there about index shifting that should be the problem.

Hope this helps,
Bill
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#6
They weren't new, I purchased secondhand - so thanks for the manuals. I have noticed that the rear mech doesn't have the original jockey wheels and the upper one does have quite a bit of play in it - does this usually affect shifting?
  Reply
#7
It very well could I would write (email) SRAM and find out.
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#8
I think it was the lower pulley that had to have some play, but maybe cyclerUK or DaveM or Alex (or somebody else) can comment on that. Also take a look at http://www.parktool.com/repair/readhowto.asp?id=76 and inspect the guide pulleys, maybe they were installed the wrong way?
  Reply


Forum Jump:

[-]
10 Latest Posts
Happy Holidays
Yesterday 05:40 PM
How to Trick out your Recumbent Tadpole ...
Yesterday 09:47 AM
How many bikes do you have now?
Yesterday 08:24 AM
Energy gels for cycling
Yesterday 06:53 AM
New , To me ..
Yesterday 04:06 AM
need e-trike advice (wife knee surgery)
Yesterday 03:58 AM
Looking for Recommendations: E-Trike for...
Yesterday 03:55 AM
How often check or change mechanical dis...
Yesterday 03:48 AM
Ketone Ester $$$
Yesterday 01:54 AM
What are the best maintenance practices ...
Yesterday 12:00 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Alexjohnson
41 posts
no avatar 2. GirishH
24 posts
no avatar 3. meamoantonio
13 posts
no avatar 4. Flowrider
13 posts
no avatar 5. Bweighmaster
9 posts