Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the October Giveaway to Win the Qiolor TIGER Retro Electric Bike


Newb needs help with Haro Backtrail X2
#21
How do i get this off? All the videos ive seen show a hammer and screwdriver, socket, etc. but there is nowhere in there for me to put anything. If thats a spacer in the center its not budging.
Heres a better pic
  Reply
#22
The picture shows cartridge bearings, with an inner race spacer.

What did it look like before you got to this point?

What is in between the shell of the frame and the outer race of the bearings? The pictures are not clear enough.
Nigel
  Reply
#23
That's a cartridge bearing conversion kit. Don't replace the bearing if it still feels smooth and there's no play in the spindle when mounted. If it's no good then just whack it out with a punch from the inside, working around the perimeter little by little till each one's out. To replace with the same Google "bottom bracket conversion" to find both parts and the procedure.
  Reply
#24
(08-26-2014, 07:00 PM)nfmisso Wrote:  The picture shows cartridge bearings, with an inner race spacer.

What did it look like before you got to this point?

What is in between the shell of the frame and the outer race of the bearings? The pictures are not clear enough.

Before that it had a spindle in it, thats it. Not sure what it is between there.
(08-26-2014, 07:05 PM)cny-man Wrote:  That's a cartridge bearing conversion kit. Don't replace the bearing if it still feels smooth and there's no play in the spindle when mounted. If it's no good then just whack it out with a punch from the inside, working around the perimeter little by little till each one's out. To replace with the same Google "bottom bracket conversion" to find both parts and the procedure.

No rotating the bearing was pretty rough. When the pedals were on they didnt rotate very well either. To get it out how do i move the spacer enough to hit inside of there? I dont need to replace it with a conversion kit do i? Could i just use american sealed or mid?
(08-26-2014, 07:00 PM)nfmisso Wrote:  The picture shows cartridge bearings, with an inner race spacer.

What did it look like before you got to this point?

What is in between the shell of the frame and the outer race of the bearings? The pictures are not clear enough.

Does this help?
  Reply
#25
The picture shows a standard industrial ball bearing (aka cartridge bearing) with its shield removed. The shiny metal part to the outside of the balls is call the outer race. The metal part to the inside of the balls is the inner race. Between the balls, under grease, is the ball retainer.

Using a punch or screw driver at an angle, hit the inner race on the opposite side; HARD, go round (with respect to the bike frame, not the inner race of the bearing) about 30° at a time, hitting the inner race each time. Two or three revolutions and the bearing will be out (and trashed). Repeat on the other side.

Take the bearings to an industrial supply house, and get matching replacement (Inner diameter and outer diameter have to match exactly).

Installing new bearings: push on the outer race ONLY. Most likely the previous owner did the installation wrong and damaged the bearings in the process. These bearings, properly installed will last many decades; even centuries. (As long as they are no subjected to washing with a solvent or water - high pressure water and soap is especially bad).
Nigel
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post

Forum Jump:

[-]
10 Latest Posts
BAGGI 1936(?)
Today 10:24 AM
Do you have a four foot rule?
Today 10:10 AM
Trek domane tyre
Yesterday 05:07 PM
Greetings!
Yesterday 04:39 PM
Peugeot Nouveau Folder
Yesterday 04:34 PM
Great UK Cycle Camping Map, For E-Bikes,...
Yesterday 12:04 PM
Community Discussion Cycling Myths
11-07-2024 09:05 PM
Cycling is Anti-Aging, But There's a Cat...
11-07-2024 06:51 PM
Tasmania! Anyone ridden here?
11-07-2024 05:15 PM
Do you plan or random ride your MTB ride...
11-07-2024 05:09 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. enkei
20 posts
no avatar 2. Jesper
18 posts
no avatar 3. GirishH
18 posts
no avatar 4. Flowrider
14 posts
no avatar 5. Talha
10 posts