Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.


Replacing Forks
#1
I am on my first of hopefully many cycle tours with my girlfriend. Last week she crashed into a small boy on a bike and although both people were fine, her bike took some serious damage. So now we need to replace the front forks of her bike. Its a Cannondale t800. The local bike store is going to try to contact Cannondale to see if they can ship us a replacement. We are in Kathmandu and the chances of us finding a replacement here are nill. The problem is we are not sure if we can afford the replacement + shipping costs. do you think it would be possible to attach some non - Cannondale forks to the bike, and what information/sizes do I need to start looking for them. I am fairly certain that the headset is threadless.

-Thanks
  Reply
#2
It is (if google is to be trusted) a rigid fork, threadless, 1 1/8" headset. In general: to make it to the next bigger town any threadless fork with a 1 1/8" diameter steerer should work. However, handling depends critically on the rake / trail of the fork. Measure the fork (unless it was bent during the crash...). What is interesting for you is: where does the line running trough the steerer hit the road in relation to the spot the wheel sits on the road. http://en.wikipedia.org/wiki/Bicycle_and_motorcycle_geometry
Try to find one that is as close as possible, otherwise you might end up with an unrideable bike. Maybe you can contact Cannondale for the specs?
  Reply
#3
thank you for the information, I am learning . . . slowly. I have seen a set of Surly Long Haul Trucker forks, that I could get shipped from the us. The rake is 45mm, its 53 on the Cannondale. Do you think this would be a close enough match?
Thanks
  Reply
#4
Let's find out!
Ok, trail is calculated by:
t= (R * cos(alpha) - r)/sin(alpha)

R=wheel radius, r=rake, alpha=steerer angle
According to people more knowledgeable than I, a trail of 50mm - 70mm is (was?) considered ok. Reducing rake increases trail. I guess that on your bike alpha=73° (around that) and t=51mm in the "normal" config. An increase should not be bad.
However: I am not a framebuilder, could somebody else check the numbers? C'mon, someone has to have the Paterek manual (or somesuch)...
  Reply
#5
Hi thanks for the help Joe_W. After hours online and after many emails later we have decided to go for some Kona project 2 forks, as they were a much cheaper option for us. We are just waiting for delivery then we can set off again!


Hope they fit ok.

Thanks again, Laurence
  Reply
#6
Awesome! Hope everything works out well and you enjoy the tour!
  Reply


Forum Jump:

[-]
10 Latest Posts
🚴‍♂️ Saddle Up for the Belgian Waffle Ri...
Today 06:15 PM
Zwift v Spin v Wahoo
Today 05:59 PM
Have you Ever Tried an Electric Bike?
Today 05:07 PM
SAVA Explorer 6061?
Today 03:31 PM
Good Morning from SW Ohio
Today 07:32 AM
(So California) PV Dr to be closed to bi...
Yesterday 09:14 PM
Tubeless vs. tubes: What are the pros an...
Yesterday 08:28 AM
The great thing about trikes
Yesterday 08:16 AM
Injury Recovery
Yesterday 08:06 AM
Fellow cyclists, we need your help! Plea...
Yesterday 08:01 AM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. GirishH
19 posts
no avatar 2. Flowrider
17 posts
no avatar 3. meamoantonio
12 posts
no avatar 4. Jake1
10 posts
no avatar 5. enkei
9 posts