Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take part in the September Giveaway for the Phantom XR electric bicycle from Life EV


Cable length problem
#1
So i went to go get a cable for gear shifting and the bike shop repair person said they are the same standard size and you cut to fit. Well the cable i got is too short for the back derailer. Are there longer gear shifting cables? Did he give me brake cables instead? Or do i have to stretch the cable or figure out how to use the shorter one?
  Reply
#2
Your bike shop person is correct. Cables are usually long enough and are cut to length when fitted (or the end coiled up).
If the cable doesn't reach then it could be, as you say a brake cable. Normally though the "nipples" on the end are a different design/size so they don't fit if wrong type.?
I do think though that you can get cables with a nipple on each end. One to suit brakes and the other end to suit derailleurs???
Ride hard or ride home alone!
  Reply
#3
In the USA; brake cables (made in China) have cast on lugs at both ends; one end for levers used on drop bars, the other for levers used on flatter bars.

see pictures in the following links:

http://www.amazon.com/Pyramid-Gear-Cable-W-Housing/dp/B000AO9QB0/
http://www.amazon.com/Pyramid-Brake-Cable-Universal/dp/B000AO7IV0/

Shifter cables are thinner than brake cables, generally around 1.2mm vs 1.5 to 1.8 for brake cables.

For most of my bikes, I purchase the pack of Bell brand cables at wal-mart. It consists of a front derailleur shifter cable (shorter), a rear derailleur shifter cable (longer), a front brake cable (shorter) and a longer rear brake cable. The cable length is more than adequate for most bikes.

I purchase special tandem length shifter and rear brake cables for our tandem at Wheel Away.
Nigel
  Reply
#4
I just went through similar trouble for my SRAM Rival shifter/brakes on my road bike. The shifter cable installation was the pits. My candidate replacement cables were as Nigel described - different lugs on both ends. However, due to the small fitting into the side of the lever, which then goes up through the middle and out the top left, the cut cable (used the Park tool) always kept fraying. I tried supergluing upon a clean cut, and even tonight, attempted soldering. Nothing worked.

Bike store had some Jagwire cables with the right lug and a sealed end (maybe electronic cut, or heat cut). They went into my shifters like butter. Amen! Never again with the dual lugs on shifter cables.

Tomorrow night I get to tweak the high/low settings of my derailleurs, and then tape, and then redoing my computer lead/sensor. My living room looks like a bike repair store blew up.

Rama, is a new cable about a foot and a half longer than your old cable? Don't cut it until you have it tightened up and aligned properly. Cut it last, before placing a cap on. My Jagwire cable has about 2 feet coming out the end of the rear derailleur.

Andrew
  Reply
#5
Rama, is a new cable about a foot and a half longer than your old cable? Don't cut it until you have it tightened up and aligned properly. Cut it last, before placing a cap on. My Jagwire cable has about 2 feet coming out the end of the rear derailleur.

Andrew
[/quote]

It turns out that while measuring wire to wire, the Jagwire cables i got were shorter, but when rewiring the bike, they were more than enough. However, when i bought the Jags they didnt come with wire clamps for the ends. Will electrical tape work instead?
  Reply
#6
(06-09-2011, 09:39 AM)Rama Owhl Wrote:  It turns out that while measuring wire to wire, the Jagwire cables i got were shorter, but when rewiring the bike, they were more than enough. However, when i bought the Jags they didnt come with wire clamps for the ends. Will electrical tape work instead?

Are you referring to crimps?
http://www.amazon.com/Jagwire-Cable-End-Crimps-SIlver/dp/B001M9IJ4M/ref=sr_1_1?s=cycling&ie=UTF8&qid=1307631149&sr=1-1

Thier sole purpose is to prevent the cable from fraying. Tape should be okay, a piece of crushed tubing would be better.
Nigel
  Reply
#7
Sounds to me like he gave you a front derailleur cable. If you change the cable you may as well change the cable housing at the same time.
  Reply
#8
Rama, you might have to ask for the wire crimps. While getting my new cables the other night at the LBS, they offered me crimps, although I got a small bag of them online with another order for a couple dollars.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
5,808
06-28-2017, 12:52 AM
Last Post: jacke
 
4,910
10-21-2014, 08:10 AM
Last Post: cny-man
 
22,190
06-20-2014, 07:14 PM
Last Post: limey
 
26,696
05-23-2014, 01:38 AM
Last Post: danny1962
 
6,632
02-10-2013, 08:12 PM
Last Post: 1FJEF
 
7,311
10-21-2011, 08:37 AM
Last Post: Joe_W

Forum Jump:

[-]
10 Latest Posts
Fixing up old bike
Yesterday 11:43 PM
[Sponsored] Souke Sports Cycling Apparel...
Yesterday 06:51 AM
Hi
Yesterday 03:11 AM
Air still trapped in the brakes
09-26-2021 06:13 PM
Fox DPX2 Damper sound
09-26-2021 04:11 PM
2021 Pro Road Cycling
09-26-2021 09:11 AM
What kind of bike do I have
09-26-2021 05:09 AM
Hello from a New Member!
09-25-2021 09:01 PM
Thesis surway
09-25-2021 05:17 PM
Advice on a bike for a new cyclist - Tri...
09-25-2021 12:03 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. ReapThaWhirlwind
24 posts
no avatar 2. Criminal
18 posts
no avatar 3. Jason @ect
12 posts
no avatar 4. Souke Sports
11 posts
no avatar 5. G_M
7 posts